Rabu, 17 April 2013



Code Error Mesin Fotocopy Canon  

E code Description      Category         Remarks         
E000    The fixing temperature does not go up after turning ON the power due to a fault in the      thermistor or the heater, etc., (e.g. It does not reach 70°C degrees within 2 min.)        Related fixing unit                 
E001    The fixing temperature abnormally goes up due to a fault in the thermistor or SSR, etc.     
E002    The fixing temperature does not reach a specific temperature due to a fault in the thermistor or the heater, etc.
e.g) The fixing temperature does not go up to 190°C degrees within 5 min after reaching 70°C degrees.  
E003    The fixing temperature drops abnormally after wait time is up due to a fault in the thermistor, the heater, etc. (e.g. After wait time is up, the fixing temperature drops to 70°C degrees). 
E004    A short circuit in the fixing heater drive circuit (SSR, etc) is detected.
E005    The fixing web is wound up completely.       
E006    The fixing drawer connector is not connected as the front door is closed.   
E007    The fixing film is off to the side.       
E008    A specific number of copies are made after the machine detects that fixing oil is out.         Since a user cannot re-supply fixing oil, the error code is indicated.        
E009    The rated voltages of the power supply and the fixing unit do not match.               
E010    Clock pulses fail to be generated or the PLL lock fails to be released due to a fault in the main motor, etc.            Related drum drive unit and main drive unit
E011    Excess current flows to the motor control circuit because the main motor is locked up, etc.           
E012    Clock pulses fail to be generated or the PLL lock is released due to a fault in the drum motor, etc.            In case the drum drive motor exists in addition to the main motor, this code refers to an error of a motor which drives mainly other units than the drum.       
E013    •The PLL lock is released because waste toner motor is locked up, etc.
•The micro switch employed to detect clogging of waste toner is activated.
•The waste toner case is detected full.                      
E014    •The PLL lock of the fixing/feeding motor is released.
•Excess current of the feeding motor is detected.     
E015    •Clock pulses of the pick-up/duplexing/developing motor fails to be generated or be detected.
•Excess current of the pick-up/duplexing/developing motor is detected.
E016    Excess current of the reciprocating motor of the photosensitive drum cleaner unit is detected.      
E017    The PLL lock of the drive motor of the holding tray unit is released.
E018    The PLL lock of the drive motor of the oil removing roller is released.
E019    The waste toner case is detected full although it is not.        
E020    The developer fails to be replenished with starter developer properly.Related developing unit        A hopper motor error is identified by the detail code of E020. However, it may be identified by E02x according to need.  
E021    The rotor fails to rotate and move properly due to a fault in the developing rotor/motor ass'y.                   
E022    Pressure fails to be applied to the developer after a specific time passes after the developer is selected.    
E023    The developer sleeve motor fails to rotate properly.  
E024    The developer cannot be detected. ( not mounted properly.)
E025    Excess current of the toner delivery motor or the cartridge motor is detected.        
E030    The total counters are not functioning.           Related counter          
E031    The optional counters are not functioning.    
E032    The counters for ASSIST are not functioning. (Disconnection of counter pulse for ASSIST.)       
E040    The lifter position signal fails to be generated due to a lifter clutch failure.  Related paper pick-up unit     
E041    The paper deck lifter fails to be detected within a specific time.      
E042    The roll paper cutting operation is not functioning properly because the cut motor does not work, etc.      
E043    An abnormal signal is detected due to a fault in the pick-up motor for the 3-cassette deck/3.5K paper deck.           
E050    A malfunction of the holding tray. A fault in the side registration is included.        Related duplex unit    The duplexing unit for the stack system   
E051    The home position of the side registration cannot be detected within a specific time.          The duplexing unit for the through-path system   
E054    The home position of the duplexing unit feed roller cannot be detected.
E055    The horizontal registration guide of the duplex unit exceeds its maximum travel distance. 
E060    The home position of the primary corona wire cleaner cannot be detected within a specific time.   Relateted charging         
E061    Specific potential is not be required or the limiter is activated as the potential is controlled.           
E062    The photosensitive drum temperature does not reach a specific value due to a fault in the photosensitive drum heater, etc.        
E063    The home position of the transfer corona wire cleaner cannot be detected.  An error code is not to be indicated.       
E064    The setting value for the output from the microcomputer considerably deviates from the control value of the actual output.             
E065    High voltage leakage from the primary corona assembly is detected.
E066    Signals from the temperature/humidity sensor cannot be detected.  
E067    Two or more faults in the primary/ pre (post)-transfer/ transfer/ separation high voltage are detected (including power output stoppage, electric leakage from the primary corona assembly).     
E068    High voltage leakage from or an open circuit in the separation corona assembly is detected.          
E069    High voltage leakage from or an open circuit in the transfer corona assembly is detected.  
E070    The home position of the transfer drum cannot be detected within a specific time.  Related transfer         
E071    An image leading edge signal cannot be detected within a specific time.    
E072    A fault in the main motors such as the transfer drum motor, etc.     
E073    The transfer drawer connector or the transfer frame drawer connector is not connected as the front door is closed.
E074    The transfer belt unit does not reach the target position within a specific time.       
E075    The transfer belt is off to the side.     
E076    The transfer belt web is wound up completely.         
E077    The motor inside the transfer belt unit has a fault.    
E079    The home position (to apply pressure) of the transfer drum cleaner unit cannot be detected.          
E080    An error occurs in the communication with the multi color unit controller PCB.      Related developing unit for multi color unit     
E081    The vertical motor clock is faulty.     
E082    The horizontal motor clock is faulty. 
E083    The CD unit horizontal movement right sensor is faulty.      
E084    The CD unit horizontal movement left sensor is faulty.        
E085    The CD unit feeder release sensor is faulty.  
E086    The CD unit claw release is faulty.    
E089    A malfunction of the multi color unit.           
E090    The document feed motor is not functioning properly.          related document feeder (bulit-into machine)           
E091    A failure in the detection of the document feed sensor.       
E100    The BD signal cannot be detected within a specific time.     Related laser  
E101    The AF motor of the laser unit is faulty.       
E102    The light intensity of the laser does not reach a specific level.          
E110    The polygonal scanner motor does not reach a specific speed within a specific time.           Related laser scnner 
E111    The polygonal cooling fan does not rotate properly. 
E120    The temperature of the laser does not reach a specific value.Related laser temperature control       
E121    The stoppage of the laser cooling fan is detected.     
E140    The movable guide motor is turned ON, and a specific position cannot be detected within a specific time.            Related BJ     
E141    1. The capping motor is turned ON, and a specific position cannot be detected within a specific time.
2. A specific position of the cam sensor for the recovery system cannot be detected within a specific time.           
E142    The pressure position switching motor is turned ON, and a specific position cannot be detected within a specific time.  
E143    The intake switching motor is turned ON, and a specific position cannot be detected within a specific time.           
E144    A detection signal is not returned to the ink pump monitor after the ink pump is activated: DCC -> BHD -> pump drive signal       
E145    No signal is generated from the position sensor within a specific time after a drive signal of the cutter motor is generated.   
E146    1. The waste ink full sensor is turned ON.
2. The intake counter for waste ink exceeds a specific value.           
E150    Neither thermistor nor trimmer resistance is connected to the head. (The head is not connected.)   Related BJ head   
E151    The thermistor of the head is open-circuited.
E152    The thermistor of the head is short-circuited.
E153    The trimmer resistance of the head is open-circuited.           
E154    The trimmer resistance of the head is short-circuited.           
E155    The trimmer resistance of the head is out of specifications.  
E156    When a specific voltage is applied to the head, the voltage of the head is not changed within a specific time.           
E157    The voltage of the head is out of the specifications. 
E160    The temperature of the head does not reach a specific temperature within a specific time.  Related BJ head temperature control    
E161    The temperature of the head exceeds a specific temperature.           
E170    When the pulse motor for the head scan is driven, it cannot be detected by a sensor within a specific time.            Related BJ head scanner        
E171    The motor is not connected to the pulse motor driver PCB for the head scan.         
E172    The gate array employed to drive the pulse motor for head scan is faulty.   
E180    The motor is not connected to the vertical scanning pulse motor driver PCB.          Related BJ paper feed           
E181    The gate array employed to drive the vertical scanning pulse motor is faulty.          
E182    After the vertical scanning motor is driven, the phase sensor cannot be detected within a specific time.    
E183    After the registration roller cam clutch 2 is turned ON, a given paper size cannot be detected within a specific time.  
E190    RAM directly connected to CPU is faulty.    Related CPU (printer unit)     Failures in RAM of the laser controller are indicated with detail codes.     
E191    An error occurs in the communication with the microcomputer (D/A converter) for high voltage use.            Machines which do not have detail code function may use this code.         
E192    An error occurs in the communication with A/D converter.  
E193    The gate array is faulty.         
E194    The auto registration is faulty.
Data from the # pattern reading CCD is invalid.      
E195    ROM failure -> No. of times data is written on EEPROM reaches the upper limit. 
E196    EEPROM failure: EEPROM read and write error (except software counter), an error in EEPROM areas on DIMM.           
E197    An error occurs in the communication within the printer:
•Errors continuously occur in the communication within the printer.
•Interruption during receiving is not made within a specific time.    
E198    An error occurs in IC on the DC controller.
Next
Posting Lebih Baru
Previous
This is the last post.

1 komentar:

untuk komentar atau konsultasi silahkan daftar dengan email anda